Browse all practice questions for the Interior Gas Piping Safety Inspection Manual Practice Test. Search by topic, open any question and review its full explanation, then test yourself in the practice quiz.

Interior Gas Piping Safety Inspection Manual Practice Test course image
More practice questions

These questions are part of the practice quiz. Start practicing

  • Which of the following is true about carbon monoxide exposure?
  • What is the primary purpose of a regulator in a gas piping system?
  • What type of gas reading should be observed to ensure safe purging procedures are followed?
  • When purging outdoors, how far must you be from a building opening?
  • What is required for gas piping at the Point of Entry?
  • Relief vents should usually be located at least how many inches away from any opening?
  • What is the primary reason for adding mercaptan to natural gas?
  • What protection is necessary for meter headers to prevent damage from impact?
  • What should be done immediately if any leak is indicated on the CGI?
  • What does the acronym CGI stand for in gas inspection?
  • Which agency regulates all piping from the gas main up to the outlet side of the gas meter?
  • During a gas leak survey, what must be checked?
  • If a leak is found on POE piping, what action should you avoid?
  • Which of the following is considered an emergency situation while inspecting gas piping?
  • What is a substandard condition regarding gas regulators?
  • Why can meter sets in unconditioned rooms accelerate the corrosion process?
  • What is the primary function of the CGI during an inspection?
  • What is the minimum distance that relief vents should typically be from an ignition or heat source?
  • Where must a regulator be installed inside a building?
  • What does a yellow flame indicate in gas combustion?
  • What are local distribution companies (LDCs) required to perform?
  • In terms of chemical composition, what percentage of hydrocarbons does natural gas contain besides methane?
  • Where is corrosion severity typically the highest in gas piping?
  • What is all piping after the gas meter outlet fitting commonly referred to as?
  • What does light surface oxide indicate?
  • When gas concentration reaches 5% and 100% LEL, what does this indicate?
  • What is the preset alarm level for carbon monoxide detection instruments?
  • What is one requirement when repairs are needed on DOT jurisdictional piping?
  • Which of the following is NOT a safety precaution to take when putting gas back into service?
  • When a head service valve or meter valve is closed, what should be done to ensure it remains secure?
  • How often should calibration of the CGI be checked?
  • What type of corrosion is indicated by peeling and scaling?
  • If a Licensed Master Plumber (LMP) encounters a situation impacting safety, what should be their first action?
  • What type of environment is required for CGI operation before an inspection?
  • Odor masking occurs when:
  • What is the role of the NYS Public Service Commission regarding gas piping?
  • What does POE stand for in gas piping terminology?
  • What is the significance of a blue flame during combustion?
  • What is the specific gravity range of natural gas?
  • What does "CO" primarily stand for in the context of gas safety?
  • What action should be taken if you notice theft of gas services?
  • What could be a symptom of defective venting systems?
  • What defines low corrosion severity?
  • What must be done for the CGI to detect a gas other than its standard gases?
  • Which of the following is NOT a requirement for the placement of gas meters?
  • What happens to mercaptan odor due to absorption by pipe materials?
  • If the plastic piping in POE piping is visibly corroded, what must be done?
  • What does a color other than blue in a flame typically indicate?
  • What should be done if the concentration of combustible gas is too high?
  • What is the preferred method for making safe a positive gas reading in a public area?
  • Corrosion severity classified as 'none or very minimal' means what?
  • When purging a gas "out of service," what should your combustible gas indicator (CGI) reading be between?
  • In an emergency situation, when must you remain on site?
  • What is the explosive limit range of natural gas?
  • What should an LMP do after closing a head service valve or meter valve?
  • What is required to proceed after the head service valve is closed?
  • What important function do valves perform in a gas system?
  • Which of the following is NOT recommended as a "make safe" action during a gas leak?
  • What concentration level of natural gas can the PS-200 detect?
  • What is atmospheric corrosion?
  • Which entities regulate the piping downstream of the gas meter outlet?
  • What is the role of sensing equipment in gas safety inspections?
  • What areas should be inspected during indoor leak survey inspections?
  • What material is not allowed on the house line and is considered an AOC?
  • Which organization sets forth the regulations for piping from the POE to the outlet side of the gas meter?
  • What is the general recommendation for the location of relief vents in gas systems?
  • What is the procedure manual used by Con Edison called?
  • Conducting interior jurisdictional piping construction falls under which task?
  • To ensure safe operation, soap tests should be conducted on what?
  • If you receive a positive gas reading in public areas, what should you do?
  • What are the NYC DOB gas piping inspection forms?
  • What type of notification is required for any severe corrosion found in gas piping?
  • What immediate action should be taken after detecting a leak?
  • Which condition does not constitute an AOC for gas systems?
  • What does the acronym DOT stand for in the context of jurisdictional piping?
  • Who should be notified immediately in the event of severe corrosion to gas piping?
  • Medium corrosion severity is characterized by?
  • Which organization inside the DOT regulates the gas piping?
  • What is considered an Abnormal Operating Condition (AOC) before the appliance valve?
  • What preliminary checks should be conducted on the CGI before starting an inspection?
  • What should be inspected on gas meters for signs of damage?
  • What is the primary common cause of atmospheric corrosion?
  • Where should the isolation of certain parts of the gas system occur?
  • What is defined as "DOT jurisdictional piping" for inside meters?
  • When assessing conditions at the meter header, which of the following is a crucial safety requirement?
  • Which factor is essential when assessing regulatory compliance regarding gas installation?
  • At the UEL of 15%, what does this mean for gas combustion?
  • What is the minimum calibration interval required for the CGI according to New York State regulations?
  • What color flame is produced by dust particles during combustion?
  • What should the discharge location be to enhance safety during indoor purging?
  • Local utility requirements must be followed by DOT jurisdictional piping, which includes which companies?
  • What does the abbreviation 'LDC' stand for in gas distribution contexts?
  • What indicates confirmed theft of service in a gas piping system?
  • Which method can be used to report emergency conditions aside from using a cell phone?
  • Which area is NOT specifically noted for inspection for corrosion?
  • Under what condition may the Local Master Plumber (LMP) turn off the head service valve?
  • What type of materials can be classified as substandard or illegal connection materials?
  • What condition can hasten the corrosion process in meter sets?
  • Mecaptan, added to natural gas, is similar in odor to what?
  • What action should be taken if a gas meter is located behind a wall?
  • If there is a gas odor detected in a commercial building, what is the first step that should be taken?
  • What is equivalent to 100% LEL in terms of gas concentration?
  • What condition indicates severe damage on a metallic surface?
  • What substance is found in smaller amounts alongside methane in natural gas?
  • What type of inspections do LDCs conduct as part of their safety protocols?
  • What are the requirements for relief vents from service regulators?
  • In an emergency due to a gas odor, what action should you take from a safe location?
  • What term is often used to refer to carbon monoxide due to its stealthy nature?
  • How is corrosion severity categorized?
  • Where must all purging be directed if boundary conditions #1 or #2 are met?
  • What indicates improper meter locations for outdoor meters?
  • According to OSHA, what is the permissible exposure limit for carbon monoxide over an 8-hour period?
  • Which of the following installations is an AOC?
  • Substandard conditions at the meter header may include a meter without which of the following?
  • Where does a service line end?
  • Who should you wait for on site during an emergency until you can leave?
  • Which of the following types of devices can be considered arcing ignition sources in a home?
  • What is the name of the valve located at the point of entry (POE)?
  • What are the two prime areas of interest within the codes that pertain to inside inspections?
  • During the process of purging a gas "into service," what should your CGI reading be at?
  • What is the main purpose of the OQ regulation?
  • Which GMI instrument model is referenced in the manual?
  • What device must be used instead of gas itself to clear a line?
  • In which quantity is carbon monoxide considered particularly deadly?
  • What term is used to describe activities involving the construction and maintenance of interior piping systems?
  • Open flame ignition sources include which of the following?
  • What is a key component of emergency response in gas-related incidents?
  • What does 'localized corrosion' primarily signify?
  • When should routine outcomes of leak surveys be reported to the utility?
  • What is an essential item to check for during an inspection of gas meters?
  • When entering a building, where should the initial gas testing occur?
  • What does UEL stand for in relation to gas safety?
  • Which of the following is an example of an illegal connection?
  • According to NYC Local Law 2016-152, how often must building gas piping be inspected?
  • What does CGI stand for in gas safety inspections?
  • How should purge end points be monitored?
  • Before starting your inspection, what calibration state must not be present on the CGI?
  • Which NFPA code covers the purging of gas piping boundary conditions criteria and procedures?
  • Which condition is categorized as Class A?
  • What type of gas is commonly used as an inert gas slug in piping systems?
  • Before starting an inspection, what is essential to do with the CGI?
  • What is a common term used to classify substandard conditions in gas pipelines?
  • What is a potential issue with a locked meter valve?
  • What is the role of GPS-1 and GPS-2 in routine reporting?
  • What must a separate device protect the system from?
  • What does AOC stand for in gas safety inspections?
  • Is today's natural gas considered toxic?
  • Compression couplings can only be installed at which locations?
  • In case of gas emergencies, which organization should NOT be contacted?
  • In terms of safety, what is the first action to take when entering a building for inspection?
  • DOT jurisdictional piping terminates at which point?
  • What is the definition of a service line?
  • What does PPM stand for in terms of gas concentration measurement?
  • During an inspection, what should LMP do regarding their findings?
  • What are common symptoms of carbon monoxide exposure?
  • Which of the following is a risk factor associated with flex hoses?
  • Where does the DOT jurisdictional piping end?
  • To whom should reports of gas service theft be directed for immediate action?
  • What should be included in a plumber's report?
  • Which of the following is a type of Abnormal Operating Condition (AOC)?
  • What is the purpose of submitting routine reporting leak survey and visual inspection results?
  • What should you do if you see a cross connection downstream of the meter?
  • At what temperature range does natural gas ignite?
  • How far must meters installed inside be from an ignition source or heat source?
  • DOT piping must comply with standards from which entities?
  • How would you best describe how carbon monoxide (CO) is characterized?
  • What is one symptom of low-level carbon monoxide exposure?
  • What is the main purpose of sealing penetration points in a building?
  • Gas piping must be properly supported and cannot be used for what?
  • What color flame indicates proper gas and air mixing during combustion?
  • High corrosion severity indicates?
  • At what gas detection percentage should all gas inspections be conducted?
  • When is the gas meter considered to be inside DOT jurisdictional piping?
  • In gas safety, why is it important to maintain proper air-to-gas ratios?
  • What substandard condition can affect outdoor gas meters?
  • When evacuating due to a gas leak, what is an appropriate action?
  • What is indicated by LEL in gas safety terminology?
  • To test the piping correctly, where should the probe be positioned?
  • What is added to natural gas to provide it with a detectable odor?
  • What is necessary to protect a gas system from atmospheric corrosion?
  • What type of piping is considered non-DOT jurisdictional after the meter outlet?
  • What should the probe be set to for proper gas detection?
  • What should be done when there is an indication of gas or odor in free air space?
  • What manual is considered a valuable tool for purging gas piping?
  • Which electrical devices are commonly known as arcing ignition sources?
  • Which of the following represents severe corrosion on painted pipe?
  • Boundary condition #1 specifies higher standards than which other boundary condition?
  • What type of device is a combustable gas indicator?
  • When installing gas piping, which type of fittings is specifically prohibited upstream of the service regulator?
  • Which type of connection is generally considered illegal?
  • What does the term "operator qualification" or "OQ" refer to?
  • What is one of the initial "make safe" actions to take upon discovering a gas leak?
  • What is the condition described as "not allowed" in relation to compression fittings upstream of service regulators?
  • What is the minimum distance from an ignition source when purging outdoors?
  • What percentage range of methane is typically found in natural gas?
  • What does the term 'backpressure' refer to in a gas system?
  • During an inspection, what two pieces of information must you confirm?
  • What is the highest level of carbon monoxide that can be lethal within three minutes of exposure?
  • Under what condition can mercaptan odors be undetectable?
  • Can a flex connector be used on a stationary appliance?
  • How are purging gas piping requirements categorized?
  • Indoor discharge of purged gases must be through an appliance burner that is not located in which area?
  • In case of a gas leak, when should the gas meter be shut off?
  • Which of the following is a source of electrical spark ignition?
  • What is the primary focus of periodic leak surveys by LDCs?
  • What is the approved time frame for calibrating the PS-200 instrument?
  • Which aspect is critical to inspect to assess corrosion severity?
  • How does the weight of natural gas compare to air?
  • What form can chemicals take in corrosive environments to affect meter sets?
  • What action should be taken for blocked vents in gas regulator systems?
  • What does "house piping" refer to?
  • What does OSHA regulate related to carbon monoxide?
  • Which aspect of a gas system do valves NOT help to regulate?
  • What requirements must each meter and regulator meet according to federal codes?
  • Which of the following characteristics best describes carbon monoxide?
  • What is the timeframe for submitting a report to NYC DOB for gas piping inspections?
  • In corrosive environments, meter sets can be affected by which of the following?
Subscribe

Get the latest from Passetra

You can unsubscribe at any time. Read our privacy policy